Good printer with a multicolor learning curve
This is a good printer, but multicolor printing requires more effort than expected. Most 3mf files online do not work correctly without file adjustments, and learning software to color 3D models is necessary for more advanced results. Printing models made of separate pieces in different solid colors is manageable, but realistic painting of a model is not currently possible. Buyers should be prepared for this learning curve before purchasing.
Pros
- + Good printer
- + Manageable with separate pieces in different solid colors
Cons
- − Most 3mf files require adjustments
- − Need to learn software to color 3D models
- − Realistic painting of a model is not possible
AI-assisted summary of a verified Amazon customer review.
· August 27, 2026 · United States
Read original on Amazon ↗
Fast, low-waste multi-toolhead printing
This first multi-toolhead printer impresses with speed and efficient filament use. Print quality is cleaner than a single-toolhead machine, likely due to CoreXY mechanics, and color swaps waste almost no filament. Some purge goes into the prime tower, which also helps produce cleaner layers. The only minor drawback is that purging occurs into the bottom of the machine, though it amounts to just a few strands. Print times and filament usage are roughly half compared to a single-toolhead setup.
Pros
- + Fast printing
- + Efficient filament use
- + Clean print quality
- + Minimal waste during color swaps
- + Prime tower helps cleaner layers
Cons
- − Purges into the bottom of the machine
AI-assisted summary of a verified Amazon customer review.
· July 6, 2026 · United States
Read original on Amazon ↗
Great in theory, but failed after update
This printer is theoretically excellent for DIY users who want to avoid wasting filament, and it is suited to creators and time-saving workflows. However, not even 35 hours in, immediately after an update, the machine began to destroy itself. There was no warning that this might happen. The return process also took until the very last minute to complete. Despite the disappointment, another unit will be ordered with the hope that the defect does not recur as soon as an update is requested.
Pros
- + great in theory
- + avoids filament waste
- + suited to DIY users
- + suited to creators
- + time-saving
Cons
- − began to destroy itself after an update
- − no warning of potential issue
- − return process took until the last minute
AI-assisted summary of a verified Amazon customer review.
· September 4, 2026 · United States
Read original on Amazon ↗
Fast, quiet, and reliable after initial issues
Two earlier units failed out of the box, but the third worked immediately. Setup is fast and easy: calibrate, install new firmware, then calibrate again. Filament loading is simple and solid, and PTFE tubing can run from a dryer to the side intakes instead of using spool holders. Color changes are quick and glitch-free, and printing is quiet. After 71 hours in four days, no failures occurred. The machine shakes noticeably, so a solid platform and correct clearance are needed; the shaking is normal and compensated for by calibration and anti-vibration feet.
Pros
- + fast and easy setup
- + quiet operation
- + quick, glitch-free color changes
- + easy and solid filament loading
- + failure-free after 71 hours
Cons
- − first two units failed out of the box
- − shakes a lot, requires a solid platform and correct clearance
AI-assisted summary of a verified Amazon customer review.
· September 2, 2026 · United States
Read original on Amazon ↗
Fast, reliable multi-material printer with minor quirks
Assembly takes about 10 minutes for the base model and slightly longer for the Pro due to the enclosure. Calibration takes around half an hour, and both units connect easily to the account and Flash studio. After 200+ hours of continuous printing, two small issues occurred: printing before a firmware update caused wrong filament channels, and a clogged nozzle from a certain filament brand. Tree supports printed too close to the model until the support XY distance was increased by 0.1mm. Print quality is impressive, filament rolls go further, and a model that took over 24 hours on another printer finished in under 7 hours. The built-in LED, connectivity, onboard camera, and time-lapse function work well.
Pros
- + Fast printing
- + Easy assembly and calibration
- + Reliable after 200+ hours
- + Good print quality
- + Working onboard camera and time-lapse
- + Improved Flash studio
Cons
- − Firmware update needed to fix filament channel issue
- − Nozzle clog with certain filament
- − Tree supports too close by default
AI-assisted summary of a verified Amazon customer review.
· August 4, 2026 · United States
Read original on Amazon ↗
